HOW TO REMOVE PENCIL, METAL & RUST MARKS FROM TILES
Step-by-step instructions for ceramic, porcelain, tessellated and terracotta tiles and other acid-resistant surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Dilute, dwell, scrub, rinse
OxiTreat+ is a Professional Grade, concentrated acid cleaner that helps remove pencil marks, metal scuffs and light rust marks from acid-resistant tiles. On walls, splashbacks and other vertical surfaces, use Oxi Gel+, the ready-to-use cling gel.
- Floors: OxiTreat+, dilute from 1:40 for light cleaning, 1:20 or stronger to disinfect (see dilution rates)
- Walls: Oxi Gel+, ready to use. See marks on wall tiles
- Minimum 10 minutes dwell time. Don't let it dry on the surface
- Scrub, pick up with a wet vac, then rinse thoroughly
- For acid-resistant surfaces only. Always test first
- Deep rust stains? See Remove Rust Stains
- Keep away from non-recommended surfaces

Where do these marks come from?
Pencil lines from setting out, grey metal marks from tools, trolleys, ladders and furniture legs, and orange rust marks from steel items left on the surface are common on new installations and busy floors.
On acid-resistant tiles these marks usually sit on the surface, so an acid cleaner and a scrub help lift them. The sooner they're treated, the easier they are to remove.
Before & after

Suitable for
- Ceramic, porcelain and tessellated tiles
- Terracotta, quarry tiles and mosaics
- Acid-resistant pavers and engineered stone
- Acid-resistant natural stone e.g. granite, bluestone, basalt, slate (test first)
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Marble, limestone, travertine, terrazzo, concrete or other acid-sensitive surfaces
- Polished surfaces, metals, chrome or glass fittings (protect them)
- Deep-set rust stains in porous stone: call us for advice
What you'll need
- OxiTreat+ (floors) or Oxi Gel+ (walls)
- Scrub'N'Clean Kit, white nylon pad or scrub brush
- Grout brush for the joints
- Plastic bucket and measuring jug (never metal)
- Broom, plus a wet vac (recommended) or mop
- Plenty of clean water and cotton towels
- Acid-resistant gloves, eye, skin and foot protection
- Optional: slow-speed scrub machine for larger areas
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Work out of direct hot sun and wind so the solution doesn't dry
- Protect metal, chrome and glass fittings, plants and any acid-sensitive surfaces nearby
- Ventilate the area well
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare the area
Sweep, vacuum or wipe the surface. Protect metal, chrome and glass fittings, plants and any acid-sensitive surfaces nearby.
2Prepare
Do a test area first
VERY IMPORTANT
Try your dilution on a small, hidden spot. Check colour stability, dark grouts and grout colourants, and how well the marks lifts. Start with the weakest dilution that works.
3Treat
4Treat
Apply evenly
Carefully apply the diluted solution to the surface with a mop or sponge. Work in sections you can keep wet.
5Treat
Allow 10 minutes dwell time
Allow a minimum dwell time of 10 minutes. Don't allow the product to dry on the surface: add more diluted product to keep it wet and active. Stubborn marks may need a longer dwell time and/or a stronger solution.
6Treat
Scrub
Scrub with a white nylon pad, scrub brush or scrub machine. Scrub dirty grout joints with a grout brush.
7Remove + rinse
Pick up and rinse
Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.
8Remove + rinse
Check when dry, repeat if needed
Check the area once it is fully dry. Repeat the process as necessary until you're happy with the result.
Dilution rates: OxiTreat+
| Use | Add OxiTreat+ per 4 L water | 1 L OxiTreat+ makes | Approx. m² per 1 L OxiTreat+ concentrate |
|---|---|---|---|
| Light cleaning – no disinfecting (1:40) | 100 mL | 41 L | 280–410 m² |
| General cleaning + disinfecting (1:20) | 200 mL | 21 L | 140–210 m² |
| Moderate cleaning + disinfecting (1:10) | 400 mL | 11 L | 70–110 m² |
| Heavy duty cleaning + disinfecting (1:5) | 800 mL | 6 L | 40–60 m² |
| Extreme cleaning + disinfecting (1:2) | 2 L | 3 L | 20–30 m² |
COVERAGE: As a guide, 1 L of diluted ready to use solution covers approx. 7–10 m², depending on the severity of the problem, how many times the process is repeated, surface porosity and texture, and site conditions.
To disinfect use 1:20 or stronger with a minimum 10 minutes wet contact time. 1:40 is for light cleaning only.
Always add OxiTreat+ to clean water to prevent splashing. Walls? Oxi Gel+ is ready to use: no dilution required.
Tips for the best result
- Treat marks early: the sooner, the easier
- Work in small sections and never let the solution dry on the surface
- Walls and splashbacks: use Oxi Gel+. See Remove Pencil, Rust & Metal Marks from Wall Tiles
- Never leave steel wool, steel tools or metal cans on tiles
- On dark grouts and grout colourants, check the test area once fully dry
Aftercare

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, for easier maintenance.

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: tessellated and terracotta tiles and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear acid-resistant gloves, protective clothing and eye/face protection
- Do NOT breathe fumes, mist, vapours or spray. Use in a well ventilated area. Do not kneel in product
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow contact with acid-sensitive surfaces, metals, chrome or glass fittings
- Do NOT mix in metal containers or with other chemicals (especially chlorine bleach)
- May affect dark grouts, grout colourants and polished surfaces
- Hard surface disinfectant only. Do NOT use on skin
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
For acid-resistant surfaces only. Do not use on marble, limestone, travertine or other acid-sensitive tile or stone. Badly stained grout may require re-grouting or re-colouring with Colour'N'Seal.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.

