HOW TO REMOVE LIGHT GROUT HAZE FROM TILES & STONE
Step-by-step instructions for porcelain, ceramic, encaustic, terrazzo and quarry tiles, natural stone and pavers, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Dilute, dwell, scrub, rinse
Haze Away is a Professional Grade, non-acidic grout haze inhibitor and cleaner for cement based, latex modified and epoxy grout. On grout haze and latex film that is less than 10 days old, use it at 1:4 for very light haze, 1:2 for light haze and 1:1 or neat for heavier haze. Used in the FINAL grout wash at 1:4 (1 L of Haze Away to 4 L of water), it helps reduce latex film and grout haze forming in the first place.
- Start with 1 L of Haze Away: 1:4 very light, 1:2 light, 1:1 or neat heavier haze
- Only for grout haze less than 10 days old
- Minimum 10 minutes dwell time. Don't let it dry on the surface
- Scrub with a white, blue or black pad (light to heavy), pick up with a wet vac, then rinse thoroughly
- Honed marble, limestone and travertine: always test first
- Very heavy haze or older than 10 days: see heavy grout haze
- Keep away from non-recommended surfaces
What is grout haze?
Grout haze is the thin, powdery or cloudy film of cement and latex left on the tile face after grouting, when the grout clean up during installation isn't thorough. It leaves tiles looking dull and dirty and can start to catch dirt.
The longer grout haze stays on the tiles, the harder it becomes to remove, so treat it early: Haze Away is for grout haze less than 10 days old.
Before & after

Suitable for
- Porcelain, ceramic, encaustic, terrazzo and quarry tiles
- Bricks, Saltillo, terracotta, concrete and pavers
- Natural stone e.g. basalt, bluestone, granite, quartzite, sandstone, slate
- Honed marble, limestone and travertine (always test first)
- Walls and floors, indoors and outdoors
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Very heavy haze or haze older than 10 days: use OxiTreat+ (floors) or Oxi Gel+ (walls) on acid-resistant surfaces
- Haze on polished natural stone and acid-sensitive surfaces: use MicroScrub
- Cured epoxy grout haze: use Aqua-Strip (light) or Strip-It (heavy)
What you'll need
- Haze Away
- Scrub'N'Clean Kit, white (light), blue (moderate) or black (heavy) scrubbing pads or a scrub machine
- Rough or heavily textured surfaces: a good quality stiff bristle brush
- Plastic bucket, measuring jug and clean water
- Sponge or mop to apply
- Wet vac (recommended) to pick up the dirty solution
- Separate bucket and mop plus plenty of clean water for rinsing
- Mask, gloves, eye, skin and foot protection
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Haze should be less than 10 days old
- Sweep, vacuum or wipe the surface
- Protect non-recommended surfaces nearby
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Sweep the surface
Sweep, vacuum or wipe the surface to remove loose dust and grit.
2Prepare
Do a test area first
VERY IMPORTANT
Try the solution on a small, hidden spot to check ease of application, dilution, colour stability and the result.
3Treat
4Treat
Apply carefully
Carefully apply the diluted solution to the surface with a sponge or mop. Work in sections.
5Treat
Allow 10 minutes dwell time
Allow a minimum dwell time of 10 minutes. Longer may be required. Don't allow the product to dry on the surface: add more diluted product to keep it wet and active.
6Treat
Scrub
Scrub with a white (light), blue (moderate) or black (heavy) scrubbing pad depending on the severity of the haze, a scrub machine or a Scrub'N'Clean Kit. Rough or heavily textured surfaces: use a good quality stiff bristle brush to get in between the texture.
7Remove + rinse
Pick up and rinse
Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water.
8Remove + rinse
Check when dry, repeat if needed
Check the area once it is fully dry and repeat as necessary. Start at 1:4 (very light), then 1:2 (light), then 1:1 or Haze Away neat (heavier). Still there? Use OxiTreat+ (acid-resistant surfaces) or MicroScrub (natural stone).
Dilution rates: Haze Away
| Use | Add Haze Away | Water | Total mixed |
|---|---|---|---|
| Final grout wash: 1:4 | 1 L | 4 L | 5 L |
| Very light haze, under 10 days: 1:4 | 1 L | 4 L | 5 L |
| Light haze, under 10 days: 1:2 | 1 L | 2 L | 3 L |
| Heavier haze, under 10 days: 1:1 | 1 L | 1 L | 2 L |
| Heavier haze, under 10 days: neat | Use as is | – | – |
Always add Haze Away to clean water. Removal: grout haze less than 10 days old only.
Final grout wash: help prevent haze
- Mix and apply the grout as per the grout manufacturer's instructions
- Do the initial heavy grout clean up with clean water
- Add 1 L of Haze Away to 4 L of clean water in a bucket (1:4)
- Do the FINAL clean up with the solution and a damp (well wrung out) grout sponge
- Wipe diagonally across the tiles and change the solution as it gets dirty
- Rinse off with a slightly damp clean grout sponge or cotton towel using only clean water
Tips for the best result
- Treat grout haze early: the older it is, the harder it is to remove
- Start at 1:4 (very light), then 1:2 (light), then 1:1 or neat (heavier)
- Work in small sections and never let the solution dry on the surface
- Change the rinse water often so haze isn't spread back over the tiles
- Haze on natural stone? See grout haze on natural stone
- For other stains, see the Stain Removal Guide
Aftercare

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce staining and make cleaning easier.

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear appropriate gloves, skin and eye protection
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow contact with non-recommended surfaces
- May affect some polished surfaces, polished natural stone and dark coloured grout: always test first
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
Haze Away is for grout haze less than 10 days old. For very heavy grout haze or haze left for over 10 days use OxiTreat+ or Oxi Gel+ (acid-resistant surfaces). For grout haze on natural stone or acid-sensitive surfaces use MicroScrub. It does not remove cured epoxy grout haze (use Aqua-Strip or Strip-It) or deep-set oil or food stains.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.

