HOW TO REMOVE ENHANCE'N'SEAL PARTIALLY CURED RESIDUE
Step-by-step instructions for natural stone, encaustic, terrazzo and porcelain tiles, pavers and other surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Apply neat, dwell, scrub, rinse
Too much Enhance'N'Seal or another stone enhancer left on the surface can cure into a sticky, blotchy or shiny residue. Strip-It, a Professional Grade heavy duty remover, stays wet for longer to help break down and remove partially cured residue.
- Strip-It: ready to use, do NOT dilute
- Minimum 30 minutes dwell, up to 2 hours (the longer the better)
- Don't let it dry on the surface: add more to keep it wet
- Scrub with Strip'N'Clean Kit - Floors (floors) or Strip'N'Clean Kit - Walls (walls), pick up with a wet vac, then rinse
- Solvent-based: ventilate well and wear gloves, eye protection and a mask
- Always test first
- Fresh or light residue: see Remove Enhance'N'Seal Residue with MicroScrub

What causes enhancer residue?
Penetrating enhancers are designed to soak into the stone. Any excess that isn't wiped off within the recommended time stays on the surface and starts to cure, leaving sticky patches, roller marks, shiny spots or a blotchy, uneven colour.
Fresh, light residue can often be removed with a non-acidic cream cleaner. Once it has partly cured, it needs a heavy duty remover with a long dwell time.
Suitable for
- Porcelain, ceramic, encaustic and tessellated tiles
- Terrazzo, mosaics, grout and concrete
- Bricks, pavers, terracotta, saltillo and quarry tiles
- All natural stone e.g. marble, limestone, travertine, granite, basalt, bluestone, sandstone, slate, and engineered stone
- Floors and walls, indoors and outdoors
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
- Industrial: warehouses, workshops, factories etc
Not for
- Fresh or light residue: try MicroScrub first
- Painted, waxed or sealed surfaces you want to keep: Strip-It will affect sealers, coatings, floor finishes, deck stains and painted surfaces
- Mixing with other chemicals
What you'll need
- Strip-It (ready to use, do NOT dilute) in a plastic container
- Roller, mop, brush or sponge to apply
- Strip'N'Clean Kit - Floors (floors) or Strip'N'Clean Kit - Walls (walls), white nylon pad, scrub brush or slow speed scrubber
- Wet vac (recommended) or mop
- XtremeClean+ for residue (optional)
- Plenty of clean water and cotton towels
- Chemical resistant gloves, eye protection and a suitable mask
- Plastic sheet and tape to protect nearby surfaces
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Use in a well ventilated area: open doors and windows, and wear a suitable mask
- Protect painted, waxed and sealed surfaces, timber, skirting and fixtures nearby
- Keep children, pets and anyone pregnant or nursing away from the area
- The floor will get slippery: plan a safe way in and out
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare and ventilate
Sweep or vacuum the area. Open doors and windows for good ventilation, protect nearby painted, waxed or sealed surfaces and put on gloves, eye protection and a suitable mask.
2Prepare
Do a test area first
VERY IMPORTANT
Try Strip-It on a small, hidden spot to check ease of application, dwell time, colour stability and how well the residue lifts.
3Treat
Apply Strip-It neat
Do NOT dilute. Pour Strip-It into a plastic container and, with a roller, mop, brush or sponge, carefully apply a liberal amount to a manageable area.
4Treat
Dwell 30 min – 2 hours
Allow a minimum dwell time of 30 minutes, up to 2 hours depending on the problem (the longer the better). Don't allow it to dry on the surface: add more Strip-It to keep it wet and active.
5Treat
Scrub
Scrub with a white nylon pad, scrub brush or scrub machine (slow speed scrubber for large areas). Focus on the sticky, shiny or blotchy patches.
6Remove + rinse
Pick up the dirty solution
Remove the dirty solution with a wet vac or mop.
7Remove + rinse
Rinse thoroughly
Rinse thoroughly with clean water. To help with any residue, apply XtremeClean+ diluted 1:5 with water, scrub again, then rinse thoroughly.
8Remove + rinse
Check when dry, repeat if needed
Check the surface once dry and repeat the process as necessary. Ready for light traffic after 1 hour or once all fumes and vapours have dissipated.
How to use Strip-It
| Product | Strip-It: ready to use, solvent-based. Do NOT dilute. |
| Dwell time | Minimum 30 minutes, up to 2 hours (the longer the better). Keep wet. |
| Coverage (neat) | As a guide, 1 L of Strip-It used neat covers approx. 7–10 m², depending on the severity of the problem, how many times the process is repeated, surface porosity and texture, and site conditions. |
| Enhancer residue | Treat the whole affected area evenly so the colour stays even. Heavy residue may need more than one application |
| Residue | XtremeClean+ diluted 1:5 with water after rinsing, scrub, then rinse again |
| Re-seal | After at least 48 hours drying. Test a new sealer or coating first |
| Lighter jobs | Fresh or light residue: MicroScrub |
Tips for the best result
- Treat the whole area, not just the worst spots, for an even colour
- Keep the product wet for the full dwell time
- Allow at least 48 hours drying, then do a test area before re-applying an enhancer or sealer
- Next time, apply enhancer thinly and wipe off all excess within the time on the label
- Ventilate well while you work and until all fumes have dissipated
- For other stains, see the Stain Removal Guide
After stripping + aftercare

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® after at least 48 hours drying (test first).

For a colour enhanced look: re-apply Enhance'N'Seal thinly to porous surfaces after at least 48 hours drying if you want the enhanced colour back. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles and pavers. Porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear appropriate gloves, skin and eye protection: causes serious eye damage
- Do NOT breathe in fumes or vapours: wear an appropriate mask. Use in a well ventilated area
- Avoid contact during pregnancy or while nursing
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow contact with painted or waxed surfaces. Will affect sealers, coatings, floor finishes, deck stains and painted surfaces
- Do NOT mix with other chemicals
- The floor will get slippery during the process. Take appropriate precautions to prevent slips and falls
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
Strip-It helps remove partially cured enhancer residue. It also removes the enhancer from the treated area, so the colour enhancement will be lighter until re-applied. Removal of thick or multiple coatings may require multiple applications of Strip-It. Allow at least 48 hours drying time before applying any sealers, coatings or floor finishes.
For stains, see the Stain Removal Guide and our Problem Solvers.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.


