Full description

About GLOSS'N'SEAL

Gloss'N'Seal is a high gloss, NanoPlus coating sealer that forms a hard wearing, durable film finish on porous, rough or textured surfaces.

Technical Bulletin (PDF) ›
Description

Gloss'N'Seal is a Professional Grade, High Performance, NanoPlus water based coating sealer that provides a high gloss film finish to porous, rough, textured surfaces.

  • Water based
  • Breathable (allows moisture vapour transmission)
  • Scuff resistant
  • Non-yellowing and UV resistant
  • Hard wearing, durable and easy to maintain
How does it work

NanoPlus coating sealer molecules chemically bond to the rough or textured surface, creating a hard wearing, durable, high sheen film. Dirt and liquids can then be cleaned off the surface more easily before they stain. Adds a high gloss finish depending on the number of coats applied.

Works on & not suitable for

Works on: all natural stone, encaustic, terrazzo, pavers etc. The surface must be porous, rough and/or textured to allow the product to properly bond. Adds a high gloss finish depending on the number of thin, even coats applied.

Not suitable for: polished or smooth surfaces, or porcelain, ceramic and tessellated tiles.

Where to use

For domestic, commercial, indoor and outdoor areas e.g. homes, supermarkets, airports, hotels, resorts, foyers, retail stores, walkways, driveways, kitchens, restaurants, bars etc.

Test first: always test in an inconspicuous area to determine ease of application, number of coats required and the final desired result. The end user must determine suitability of the product for their own use.

What you need & preparation

Preparation of surface: use XtremeClean+ or Stone Wash+ to clean and prepare the surface before sealing.

  • Protective gloves, eye and skin protection
  • XtremeClean+ or Stone Wash+ to clean and prepare the surface for sealing
  • Sealer applicator, paint roller or paint pad, plus a suitable plastic container or paint tray
How to use
  1. Sweep, vacuum or wipe the surface
  2. Apply Gloss'N'Seal sealer to a clean, dry surface using a sealer applicator, paint roller or paint pad
  3. Ensure even coverage with a thin film coat - do not apply thick or heavy coats. Apply thin even coats for the best final result
  4. Avoid overworking the product to avoid air bubbles and drag marks
  5. 'Feather' back to remove excess sealer and streak marks to leave a thin even film with no streak marks or puddling
  6. Apply the next coat as soon as the previous coat is dry to the touch - minimum 30 minutes between coats
  7. Apply the next coat crossways to the previous application, e.g. 1st coat in a north-south direction and 2nd coat in an east-west direction
  8. Apply a minimum of 2 thin coats. Apply more coats until the desired level of gloss is reached. When applying subsequent coats, repeat steps 2-7
  9. The surface is ready for light traffic when dry (minimum 6 hours). Keep the surface dry for a minimum of 24 hours. Full cure in 24-48 hours

Tip: if further slip resistance is required, add Grip-It P Powder (anti-slip powder additive) to the final coat.

Coverage

Approximately 40-60 m² per 4 litres per coat of Gloss'N'Seal. Coverage will vary depending on the porosity and texture of the surface, weather conditions, application method and number of coats required.

Limitations

Gloss'N'Seal is a coating sealer, not a waterproofing membrane: it will not prevent surface wear or etching from harsh or acidic chemicals. Wipe spills as soon as possible to help reduce staining and slip falls. Do not use in areas where puddling water might occur or where there is insufficient water run off.

Expected wear & maintenance

Expected wear: will vary depending on surface texture and hardness, traffic wear, plus the frequency and type of cleaning products used. Harsh cleaning including pressure washing, high alkaline, acidic or solvent-based cleaners and/or weather exposure will affect wear and performance. High traffic and exterior areas will require more frequent re-application. Re-seal as necessary.

Maintenance: apply additional coats of Gloss'N'Seal over time as required. Only use EzyClean+ for routine, everyday/weekly cleaning and disinfecting. It is an easy to use, rinse free and streak free, concentrated pH neutral cleaner that does not affect the coating sealer or the sealed surface.

Stripping: use either Aqua-Strip or Strip-It, depending on the number of coats that have been applied over the years, when it's time to remove the existing coating and start afresh.

Precautions & safety directions
  1. Read the entire label, SDS and technical bulletin before using
  2. Wear appropriate gloves, skin and eye protection
  3. Use when the surface temperature is between 4°C and 28°C
  4. Surface must be clean, dry and free from sealers and coatings
  5. Do not allow sealer to drip or leave drip marks
  6. Do not saturate the open grout joints
  7. Do not use on the underside of tiles
  8. Do not use on smooth or polished surfaces - the coating sealer requires a rough or textured surface to properly bond to
  9. Avoid dragging furniture across the coating sealer to avoid scratches or damage to the coating
  10. Not for use on smooth surfaces or bench tops, table tops etc
  11. Not recommended for use in areas subject to standing or pooling water, e.g. showers, swimming pools, spas etc. If using outdoors, ensure adequate water run off to help prevent pooling water

Test first in an inconspicuous area to determine ease of application, number of coats required and the final desired result.

Handling, storage, clean up & first aid

Handling & storage: close the container tightly after each use. Store in the original container between 4°C and 32°C. Shelf life is approximately 3 years in an unopened container - less after opening. Storage beyond that time does not necessarily mean the product is not usable; do a small test area first. Do not re-use the container, discard in rubbish. Clean tools and clothing with water before they dry.

First aid: contact the Poisons Information Centre (Australia Ph: 131-126, NZ Ph: 0800 764-766). Avoid contact with skin and eyes. Do not swallow; if swallowed do not induce vomiting, rinse mouth well with water. If in eyes, hold eyelids apart and immediately flush the eye with clean, running water for at least 15 minutes and see a doctor. If on skin, wash thoroughly with water. If feeling unwell, seek medical attention.

What to use on

Finishes

  • Flamed
  • Rough/Highly Textured
  • Sand Blasted
  • Textured
  • Tumbled

Tap a surface to see every product for it. Always test in an inconspicuous area first. Not sure? Use the Product Selector below.

How much do I need?

WATCH: HOW TO USE

How to apply Gloss'N'Seal

Penetrating vs coating sealers

  • 5 stars: 2 (100%)
  • 4 stars: 0 (0%)
  • 3 stars: 0 (0%)
  • 2 stars: 0 (0%)
  • 1 star: 0 (0%)
A
Anonymous

Fantastic product!

J
Jan

Very easy to apply. Dries quickly with minimal odour. Looks fabulous.

Chat on WhatsApp