HOW TO DARKEN & SEAL LIGHT OR FADED GROUT

Step-by-step instructions for cement-based grout between glazed ceramic and porcelain tiles, on walls and floors, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Grout · Darken & seal

Clean, dry, enhance, wipe

Enhance'N'Seal is a Professional Grade, premium, 100% actives penetrating sealer and colour enhancer. Worked into clean, dry cement grout, it helps darken and enrich light or faded joints for a richer, no sheen look, and seals the grout to help resist stains from oil, food, grease and grime.

  • Darkens the existing grout colour: it does not change the colour or hide stains
  • Grout must be clean, COMPLETELY dry and unsealed. Clean with XtremeClean+
  • Keep wet 10 – 15 minutes, then wipe COMPLETELY dry
  • We definitely recommend 2 coats for best results, minimum 30 minutes apart
  • Darkens any porous surface it touches. CANNOT be reversed
  • Not for epoxy grout. Always test first
  • Keep away from non-recommended surfaces
Enhance'N'Seal 4 kg
ENHANCE'N'SEAL
250 g · 1 kg · 4 kg
$116.00 View product

Why does grout go light or faded?

Cement grout is porous and always dries lighter than it looks when wet. Over time, wear, sunlight and harsh or acidic cleaners can wash out the surface of the joint, so the grout looks pale, chalky or patchy against the tiles, even when it's clean.

Enhance'N'Seal penetrates the grout and lines the pores. This deepens the colour, much like the look of wet grout but without a shine, and leaves the joints sealed so spills can be wiped up before they stain.

DARKEN OR RE-COLOUR? Enhance'N'Seal darkens and enriches the colour the grout already has. To change the colour or cover stained, blotchy grout, use Colour'N'Seal (25 colours). See Re-Colour & Seal Stained, Blotchy Grout.

Light, faded grout

Light, faded grout

Suitable for

  • Cement-based (sanded and un-sanded) grout
  • Grout between glazed ceramic and porcelain tiles, where excess is wiped off the tile face
  • Grout between natural stone being colour enhanced with Enhance'N'Seal at the same time
  • Walls and floors, indoors and outdoors

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Epoxy grout, or grout already sealed or coloured (e.g. Colour'N'Seal)
  • Stained, blotchy or patchy grout: re-colour with Colour'N'Seal
  • Unsealed porous stone or unglazed tiles you don't want darkened
  • Cracked or crumbling grout: re-grout first

What you'll need

  • Enhance'N'Seal
  • XtremeClean+ and a grout brush to clean the joints
  • Small sealer brush, artist brush, kids' toothbrush or a sponge cut to size to suit, and a small tray
  • Painter's tape to mask porous surfaces nearby
  • Plenty of clean, absorbent cotton cloths or paper towels
  • Moisture meter (showers and wet areas)
  • Mask, gloves, eye, skin and foot protection. Use in a well ventilated area

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Grout must be clean, COMPLETELY dry and free from sealers, colourants and coatings
  • Sprinkle water on the grout: it should darken and soak in. If it sits on top, the grout is already sealed
  • Protect porous surfaces nearby: darkening CANNOT be reversed
  • Work out of direct hot sun and wind

Step-by-step

Prepare → Enhance → Finish
Clean the grout1Prepare

Clean the grout

Clean the grout with XtremeClean+ at 1:10 (1:5 for heavy grime) as per the label. Scrub the joints with a grout brush, then rinse thoroughly with clean water and pick up the rinse water.

Let it dry COMPLETELY2Prepare

Let it dry COMPLETELY

The grout must be clean, COMPLETELY dry and free from sealers, colourants and coatings. Allow at least 24 hours, longer in showers, cold or humid weather. A moisture meter helps in wet areas.

Do a test area first3Prepare

Do a test area first

VERY IMPORTANT
Wet a short joint with plain water: the wet colour gives a rough preview of the darker look. Then apply Enhance'N'Seal to a short, hidden joint and check the colour, the number of coats and how easily it wipes off the tiles once dry.

Protect porous surfaces nearby4Prepare

Protect porous surfaces nearby

Enhance'N'Seal darkens ANY porous surface it touches, and the darkening CANNOT be reversed. Mask off unsealed natural stone, unglazed tiles, timber, render and thresholds next to the grout with painter's tape.

Apply Enhance'N'Seal to the joints5Enhance

Apply Enhance'N'Seal to the joints

Pour a little into a small tray. Apply along the grout joint with a small sealer brush, artist brush, kids' toothbrush or a sponge cut to size to suit, keeping it on the grout and off the tile face as much as possible. The most important thing is we want a scrubbing action to push the product into the grout. Ensure an even coat. Walls: work bottom to top and avoid run-down.

Keep it wet for 10 – 15 minutes6Enhance

Keep it wet for 10 – 15 minutes

DON'T ALLOW IT TO DRY ON THE SURFACE: ADD MORE TO KEEP IT WET FOR 10 – 15 MINUTES. Work in small sections (about 1 – 2 m²) so you can keep each section wet and wipe it in time.

Wipe COMPLETELY dry7Enhance

Wipe COMPLETELY dry

After 10 – 15 minutes, wipe the tiles and joints COMPLETELY DRY with absorbent paper or cotton towels. Leave no sealer on the tile face: on glazed tiles any excess left to dry becomes a sticky or hazy residue that is extremely hard to remove.

2nd coat for best results, then cure8Finish

2nd coat for best results, then cure

Apply a 2nd coat the same way after a minimum of 30 minutes: we definitely recommend 2 coats for best results. 2 hours after the final coat, sprinkle a few drops of water on the grout: if it soaks in easily, apply another coat. Light traffic after 2 hours; keep dry min. 48 hours.

Approximate coverage: Enhance'N'Seal

Tile size (3 mm joint) Per 250 g per coat (2 recommended) Per 1 kg per coat (2 recommended)
200 × 200 mm approx. 20 m² approx. 80 m²
300 × 300 mm approx. 30 m² approx. 120 m²
400 × 400 mm approx. 40 m² approx. 160 m²
600 × 600 mm approx. 60 m² approx. 240 m²

We definitely recommend 2 coats for best results. Coverage depends on grout porosity, joint width and depth, application method and number of coats.

Drying & curing (20°C)

Stage Time
Keep wet, then wipe completely dry 10 – 15 minutes
Between coats Min. 30 minutes
Water drop test 2 hours after final coat
Light foot traffic After 2 hours
Keep dry / full cure Min. 48 hours

Porous or very faded grout may need a 3rd coat. Clean tools with mineral spirits before they dry.

Which product for your grout?

What you want Product
Darken light or faded grout and seal it (no colour change) Enhance'N'Seal
Change the colour, or cover stained, blotchy grout (25 colours) Colour'N'Seal
Keep the natural colour and seal it Aqua-Seal Gold+®
White salts on the grout (efflorescence) Remove efflorescence first

Not sure? Try the Product Selector or contact us on +61 2 9521-4000.

Tips for the best result

  • Preview the look first: wet a joint with water. The enhanced colour is close to how the grout looks wet, without the shine
  • Work a small section at a time so the sealer never dries on the tiles
  • Use a small brush along the joint: less product on the tile face means less wiping and a cleaner finish
  • We definitely recommend 2 coats for best results: two thin, even coats wiped completely dry look and wear better than one heavy coat
  • Missed a spot and it dried on the tiles? See Remove Enhance'N'Seal Residue
  • Re-apply as the enhanced effect fades: when water soaks in quicker, apply a maintenance coat of the original sealer

Aftercare

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Enhance'N'Seal

Enhance'N'Seal: re-apply as the enhanced effect fades or when water soaks in quicker (water drop test).

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear a mask, gloves, skin, eye and foot protection. Use in a well ventilated area
  • Use when the surface temperature is between 4°C and 32°C
  • Grout must be clean, dry and free from other sealers and coatings
  • Enhance'N'Seal darkens any porous surface it touches. Once enhanced, it CANNOT be restored to the original look
  • Do NOT allow sealer to dry on the surface or leave drip marks: wipe completely dry
  • Not for epoxy grout, glazed or non-porous tile faces
  • Do NOT use acidic or harsh cleaners on the sealed grout
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

Enhance'N'Seal is a penetrating sealer, not a waterproofing membrane, and is not a substitute for a compliant damp-proof membrane, drainage or correct substrate preparation. It darkens the existing grout colour: it won't change the colour, hide stains or repair cracked grout. Results vary with the grout colour, porosity and condition. Wear depends on traffic and cleaning: re-apply as necessary.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp